Practice MCQs and read articles about Mechanical Engineering
20 of 50 Mechanical Engineering questions, shown with their correct answers — open an answer to check yourself, then practice the full set free.
A solid circular shaft is subjected to a torque of 1500 N m. If the allowable shear stress is 60 MPa, the required diameter is approximately (using pi = 3.14):medium
Correct answer: 50 mm
The module of a gear is defined as the ratio of the:easy
A live look at what's newest across TestGenius
Which mosque did the Holy Prophet (PBUH) lay the foundations of on his arrival at Quba during the Hijra?
Practice thisUnder section 71 of the Elections Act 2017, on what kind of paper must ballot papers be printed?
Practice thisPractice 50 Mechanical Engineering multiple-choice questions from Academic & Professional Subjects, covering easy, medium and hard level questions (25 easy, 15 medium, 10 hard). Attempt a batch, check each answer instantly and repeat as often as you like — free, with no signup. Explore more subjects in Academic & Professional Subjects.
Mechanical Engineering sits in Academic & Professional Subjects and currently has 50 practice questions: 50% easy, 30% medium, 20% hard. This set leans towards easier questions, which makes it a comfortable starting point before moving on to harder material.
With 50 questions, doing about 25 a day would take roughly 2 days to complete once.
Examples of questions in this subject:
There are 50 Mechanical Engineering MCQs on TestGenius (25 easy, 15 medium, 10 hard), as part of Academic & Professional Subjects. You can practise all of them free on this page.
Yes. Mechanical Engineering practice on TestGenius is completely free and guest practice needs no signup. Creating a free account unlocks unlimited questions, timed quizzes and certificates.
Yes. A sample of Mechanical Engineering questions with their correct answers is shown on this page, and in the practice session every answer is checked instantly as you attempt it.
Work through the Mechanical Engineering questions in batches, review each correct answer after you attempt it, and repeat the questions you got wrong until you can answer them confidently. Then take a timed quiz to check yourself under exam pressure.
Correct answer: Pitch circle diameter to the number of teeth
The maximum shear stress in a shaft of diameter 50 mm subjected to a torque of 2000 N m is approximately:hard
Correct answer: 81.5 MPa
The emissivity of a perfectly black body is:easy
Correct answer: 1
A simply supported beam of span 6 m carries a uniformly distributed load of 4 kN/m over the whole span. The maximum bending moment is:easy
Correct answer: 18 kN m
The slenderness ratio of a column is the ratio of its effective length to the:medium
Correct answer: Least radius of gyration
The COP of a vapour absorption refrigeration system is typically:easy
Correct answer: About 1
In a vapour compression refrigeration plant, the refrigerant after passing through the throttling (expansion) valve has:easy
Correct answer: Low pressure and low temperature
The draft tube in a reaction turbine is used to:hard
Correct answer: Convert the kinetic energy at the outlet into pressure energy and reduce exit losses
The Oldham coupling is used to connect two shafts which are:hard
Correct answer: Parallel with a small lateral offset
The Kelvin-Planck statement of the second law of thermodynamics deals with the:hard
Correct answer: Conversion of heat into work
The Francis turbine is a:medium
Correct answer: Mixed flow reaction turbine
The efficiency of a Carnot engine working between 127 degrees C and 527 degrees C is:easy
Correct answer: 50 percent
The section modulus of a rectangular section of width b and depth d is:easy
Correct answer: bd^2 / 6
Taylor's tool life equation is expressed as:hard
Correct answer: VT^n = C
Whitworth quick return mechanism is an inversion of the:hard
Correct answer: Single slider crank chain
The point of contraflexure in a beam is the point where the:easy
Correct answer: Bending moment changes its sign
A Pelton wheel is most suitable for:medium
Correct answer: High head and low discharge
A pitot-static tube in fluid flow is used to measure the:easy
Correct answer: Local velocity of flow at a point
In an open belt drive, if the driver pulley rotates clockwise when viewed from one side, the driven pulley rotates:easy
Correct answer: Clockwise
In a field of research, a small number of authors publish many papers while most authors publish only one. Which bibliometric law describes this pattern of author productivity?
Mechanical Engineering sits in Academic & Professional Subjects and currently has 50 practice questions: 50% easy, 30% medium, 20% hard. This set leans towards easier questions, which makes it a comfortable starting point before moving on to harder material.
Yes — signed-in users can take a timed quiz in any subject and earn a certificate by passing it. Practice mode itself is untimed and does not issue certificates.